*** CLEARANCE SALE ***

  • SerialStat V2

    Serial communications monitor/tester

$8.00 + Shipping --- Part #RSSV2

  • RS232 Patcher

    Custom serial patching module. Making custom serial line patches are a snap with this handy little module. Standard 0.1" spaced headers can accept a standard wire wrapping tool to make the connections. Great for prototyping or temporary interfacing.

$8.00 + Shipping --- Part #RSPWOC

  • TTL-RS232 Bridge


    - Translates TTL and RS232 serial data bi-directionally
    - Two complete channels
    - On-board 5V regulator and filtering capacitors
    - Screw terminal blocks make connections quick and easy, without need for soldering
    - Can be powered with +9-20VDC
    - Regulated +5VDC available at terminal for external use

$15.00 + Shipping --- Part #RTTLRS232B

  • DB9 Male SIP Adapter - Comes with pre-soldered pin header

    • $2.00 + Shipping --- Part #RSIPDB9M

  • DB9 Female SIP Adapter - Comes with pre-soldered pin header

    • $2.00 + Shipping --- Part #RSIPDB9F

  • RJ-11/12 SIP Adapter - Comes with pre-soldered pin header

    • $1.00 + Shipping --- Part #RSIPRJ12

  • RJ-45 SIP Adapter - Comes with pre-soldered pin header

    • $1.00 + Shipping --- Part #RSIPRJ45

  • MiniDin 6 Pin SIP Adapter - Comes with pre-soldered pin header

    • $2.00 + Shipping --- Part #RSIPMD6

  • PIC18F252 Development Module

    Breadboard pluggable module with built-in 5V power supply, filtering capacitors and 20 MHz resonator

    Datasheet Download: PIC18F252 Development Module

$15.00 + Shipping --- Part #RP18F252DM

  • RS232-TTL SIP Adapter

    This module allows for easy interfacing of your serial devices to any TTL application. Works great with all microcontroller projects! Includes DB9 Female connector installed for direct connection to a computer's serial port.

    Datasheet Download: RS232-TTL SIP Adapter

$10.00 + Shipping --- Part #R232TTLSIP

Take the guesswork and time out of developing with an HD44780 based LCD display!

    Features
  • Simple to use!
  • Only needs power, ground, control and data lines
  • Works with any HD44780 based character display
  • Pin header interface or RJ45 jack
  • On-board contrast and brightness potentiometers
  • Great for Arduino projects
  • Lightning fast prototyping!
  • Remote display using a standard CAT5 cable. We tested up to 25 feet!
$10 + Shipping --- #LCDPBP

  • Active GPS Patch Antenna

    - Low cost GPS patch antenna
    - Built-in 3V active pre-amp
    - Male SMA connector with 16 foot RG-174 cable
    - Small, compact size at 45mm x 35mm x 15mm (LxWxH)
    - Built-in rare earth magnet for firm holding power
    - This is the antenna ONLY, not a complete GPS receiver.

$8.00 + Shipping --- Part #RGPSA

  • Garmin Round Connector to Serial Cable with +12VDC Lighter Adapter

    WILL NOT WORK WITH 8V UNITS! ATTEMPTING TO USE WILL KILL YOUR GPS!

$10.00 + Shipping --- Part #RGRSERPWR

  • Garmin eTrex (Flat) Connector to Serial Cable

    Compatable with Garmin models: eTrex Series, eMap and Geko

$8.00 + Shipping --- Part #RGETREXSER

  • Garmin eTrex, eMap and Geko Flat Connector to Serial Cable with +12VDC Lighter Adapter

$10.00 + Shipping --- Part #RGESERPWR


  • ARM JTAG Programmer

    • - Standard parallel port interface to computer
    - Based on popular Wiggler design
    - Works well with free H-Flasher/H-JTAG programming software
    - Includes 20 pin target ribbon cable with standard JTAG pinout
    - Programs all ARM7 and ARM9 variants. Including CORTEX-M3 targets.
    - Powered from target circuit
    - Built-in header makes connecting custom flash adapter cables easy

    Manual: ARM JTAG Programmer

    $12.00 + Shipping --- Part #RARMPGM